021 949 2265 service@vft.co.za

Blowers

Supply and Installation of Leading, Trusted Brands of Blowers in the Western Cape.

Our highly experienced team understands that as a business operating a controlled environment – such as a laboratory, processing facility or manufacturing facility – that you require a superior vacuum pump or blower, customised to suit your needs, that performs with consistent reliability cycle after cycle.

In addition to the supply and installation of standard and customised vacuum pumps and blowers, we are also skilled in the overhaul and servicing of all vacuum pump and blower brands.

HAVE YOU EXPLORED OUR OTHER WATER, SEWAGE, VACUUM AND AIR HANDLING SERVICES, PRODUCTS AND SOLUTIONS?

We have so much more to offer you…

The Greenco range of side channel blowers are available in single stage as well as two stage units. The Greenco range of side channel blowers comes as a complete unit and is easy to install.

GREENCO 2RB

GREENCO 2RB type can be applied both as vacuum pump and compressor in continuous operation over the total stated performance curve range. The motors are available as standard for the input voltage range of 50 and 60 Hz and for protection category IP 54 as well as approbated for EC and ROHS.

These motors are designed according to the DIN EN 60 034 / IEC 34-1 and temperature class F. For the three phase machines the tolerances +/- 10% for fixed voltage and for +/- 5% voltage range. The single phase machines are designed with a +/- 5% tolerances.If only 90% of the maximum allowed pressure will be used for continuous operating then the allowed voltage range add to +/- 10%. The frequency tolerances is maximum +/- 2%.

GREENCO G-4RB

All G-4RB achieve the standards and norms of the low voltage directive (LVD)2006/95/EC, rotating electro-technical motor EN 60034-1-2004, electromagnetic compatibility (EMC)EN55014-1/2,EN61000-2/-3/-4/-6.
For standard UL for ELECTRIC MOTOR UL 1004-1.
Relief-valves are available for limiting differential pressure.
Measuring-surface sound-pressure level acc. to DIN EN 21680, measured at a distance of 1 m. The pump is throttled to an average suction pressure, a hose is connected to the discharge side (compressor) / suction side (vacuum pump), but is not fitted with relief valves.
The motors are designed according to the DIN EN 60 034 / DIN IEC 34-1 and temperature class F.
For the three phase machines the tolerances are +/- 10 % for fixed voltage and +/- 5 % for voltage range.
The single phase machines are designed with a +/- 5 % tolerances. If only 90 % of the maximum allowed pressure will be used for the continuous operating then the allowed voltage range add to +/- 10 %.
For all single and three phase machines which designed according to the UL and CSA norm (UL 1004-1) the maximum allowed voltage tolerances are – 10 % resp. + 6 %.
The frequency tolerance is maximum +/- 2 %.

Pressure Relief Valves

The Greenco Relief Valve is constructed of zinc-plated mild steel and is designed to protect blowers from overheating in a blocked-off mode during vacuum or pressure operation. Each valve can be set by the customer to the desired vacuum or pressure level. Commonly used in Regenerative, Positive Displacement Blowers and Vacuum Pumps.

Work Principle

The relief valve is installed on inlet or outlet of side channel blower.
When the working pressure or pressure surge inside the blowers is overload than the rated pressure of side channel blower, the relief valve will be open within 0.2 minutes; the overload pressure will be released from relief valve in order to protect the blower.
When the working pressure reduces the safe value, the valve will be closed slowly; this will not cause the pressure surge again.

Materials & Specification

Both inside and outside is steel.
Can be used both pressure and vacuum.
Connect thread suitable for PT, PF and NPT.

Phone: 021 949 2265

Fax: 086 695 7460

Jaco van Blerk: 083 234 9603 | jaco@vft.co.za

Johan de Kock: 083 652 1546 | johan@vft.co.za

Wayne Fielies: 082 312 1331 | wayne@vft.co.za

Email: admin@vft.co.za service@vft.co.za

Based in Stikland, Cape Town, Vacuum and Fluid Technology assists companies within the water, waste and industrial sectors with a wide range of innovative, premium quality Water, Sewage, Vacuum and Air Handling components, products and systems. We manufacture for both the Local and Export market.

Unit 9-12, Hydro Park 1, Hydro Street, Stikland, Western Cape, South Africa
PO Box 430, Gordons Bay, 7151